Skip to content
*** 2 Products in . 1 bottle Carbon & Iron/ Trace/Fulvic Acid enhancing plant growth***
LCA Carbon PLUS will increase carbon level while inhibiting algae growth. The 'PLUS' is the added trace elements of Iron, Zinc, Magnesium etc, designed to improve plant growth.
You are basically getting 2 products in one bottle !
There are no added phosphates or nitrates.
Using an efficient bottle pump dispensing system means less mess for you and easier handling. As always with LCA, our products are high quality and value for money. Offering you the best, so your tanks can be the best!
An excellent companion to our All-In-One Fertiliser and it's shrimp/fish friendly.
Dosage
On initial use and immediately after 50% weekly water change.
6 pumps ( 12ml) per 100L
Daily maintenance
1 pump ( 2ml ) per 100L
Safety Directions
Avoid contact with skin and eyes. If eyes are exposed wash immediately with water and seek medical attention. If swallowed, contact Poisons Information Centre immediately ( Ph : 131126 )
Analysis
1 pump in 100L yields
Glutaraldehyde - 0.3ppm
Citric acid - 0.1ppm
Iron - 0.025ppm
Magnesium - 0.0035ppm
Zinc - 0.019ppm
Copper - 0.00015ppm
Manganese - 0.0085ppm
Boron - 0.004ppm
Molybdenum - 0.0002ppm
LCA Carbon PLUS will increase carbon level while inhibiting algae growth. The 'PLUS' is the added trace elements of Iron, Zinc, Magnesium etc, designed to improve plant growth.
You are basically getting 2 products in one bottle !
There are no added phosphates or nitrates.
Using an efficient bottle pump dispensing system means less mess for you and easier handling. As always with LCA, our products are high quality and value for money. Offering you the best, so your tanks can be the best!
An excellent companion to our All-In-One Fertiliser and it's shrimp/fish friendly.
Dosage
On initial use and immediately after 50% weekly water change.
6 pumps ( 12ml) per 100L
Daily maintenance
1 pump ( 2ml ) per 100L
Safety Directions
Avoid contact with skin and eyes. If eyes are exposed wash immediately with water and seek medical attention. If swallowed, contact Poisons Information Centre immediately ( Ph : 131126 )
Analysis
1 pump in 100L yields
Glutaraldehyde - 0.3ppm
Citric acid - 0.1ppm
Iron - 0.025ppm
Magnesium - 0.0035ppm
Zinc - 0.019ppm
Copper - 0.00015ppm
Manganese - 0.0085ppm
Boron - 0.004ppm
Molybdenum - 0.0002ppm
Q: How much is postage cost?
A: All dry goods are $8.95 flat shipping, $11.95 for Plants express postage and live stock are $20 express postage flat. Handling time applies.
Q: Where do we ship ?
A: We ship Australia wide but Live stock are not shipped to WA,NT & Tasmania because of the state law.
Q: Where do we ship from ?
A: We ship from Sydney,
Q: When do we ship ?
A: All dry goods are shipped Monday - Friday. Live Goods are shipped Mon - Wed depending where you are.
Q: Can I Pick Up ?
A: We are not offering any pickup at this stage
A: All dry stock can be returned back. Live goods are not refundable. Shipping cost will be deducted upon return of the item and also customer is responsible to send the item back.
We dont ship Live stock and plants to WA,NT & Tasmania because of the state law.
We do ship dry goods.
We do ship dry goods.
Drip acclimation is a method used to gradually introduce aquatic animals, such as shrimp, snails, and fish, to their new tank environment after transport. It helps them adjust to the water parameters and temperature differences between the transport bag and the tank. Here's a step-by-step guide on how to drip acclimate your aquatic animals:
Step 1: Prepare the necessary materials
Clean bucket or container large enough
Airline tubing
Air pump (optional but recommended)
Adjustable valve or knot (to regulate the flow of water) or get a abquatics drip kit
Clean, dechlorinated water (ideally matching the temperature and pH of your tank)
Step 2: Set up the drip acclimation system
Fill a clean bucket or container with the clean, dechlorinated water.
Attach one end of the airline tubing to an air pump (if using) and place the other end inside the bucket. Make sure it reaches the bottom of the container.
Step 3: Start the drip
Open the bag containing the aquatic animals and carefully pour the entire contents into the bucket, including the water from the transport bag.
Start a siphon by sucking on the free end of the airline tubing or use a siphon starter. This will initiate a slow drip of water into the bucket.
Step 4: Adjust the drip rate
Use an adjustable valve or tie a knot in the airline tubing to regulate the drip rate. Aim for approximately 2-4 drips per second.
The slow drip helps gradually mix the water in the bucket with the water from the transport bag, preventing any sudden changes in water parameters.
Step 5: Monitor the process
Keep an eye on the acclimation process and periodically test the water parameters in the bucket using a test kit. This helps ensure a smooth transition.
Depending on the sensitivity of the animals and the water parameters involved, the acclimation process may take anywhere from 30 minutes to a few hours.
Step 6: Adjust water volume if needed
If the water volume in the bucket becomes too high, you can remove some water and continue the drip acclimation process with fresh, dechlorinated water. Be cautious not to remove too much water, as it can lead to sudden changes in water parameters.
Step 7: Transfer the animals to the tank
Once the acclimation process is complete, gently net the aquatic animals from the bucket and transfer them to the tank. Avoid adding the water from the acclimation container to the tank to prevent any potential contamination.
Step 8: Dispose of the acclimation water
After transferring the animals, discard the acclimation water from the bucket. Do not pour it directly into any drains or natural bodies of water.
By following these steps, you can safely and gradually acclimate your shrimp, snails, and fish to their new tank environment after transport. Remember, it's important to monitor the process closely and make adjustments as necessary to ensure a smooth transition for your aquatic pets.
Step 1: Prepare the necessary materials
Clean bucket or container large enough
Airline tubing
Air pump (optional but recommended)
Adjustable valve or knot (to regulate the flow of water) or get a abquatics drip kit
Clean, dechlorinated water (ideally matching the temperature and pH of your tank)
Step 2: Set up the drip acclimation system
Fill a clean bucket or container with the clean, dechlorinated water.
Attach one end of the airline tubing to an air pump (if using) and place the other end inside the bucket. Make sure it reaches the bottom of the container.
Step 3: Start the drip
Open the bag containing the aquatic animals and carefully pour the entire contents into the bucket, including the water from the transport bag.
Start a siphon by sucking on the free end of the airline tubing or use a siphon starter. This will initiate a slow drip of water into the bucket.
Step 4: Adjust the drip rate
Use an adjustable valve or tie a knot in the airline tubing to regulate the drip rate. Aim for approximately 2-4 drips per second.
The slow drip helps gradually mix the water in the bucket with the water from the transport bag, preventing any sudden changes in water parameters.
Step 5: Monitor the process
Keep an eye on the acclimation process and periodically test the water parameters in the bucket using a test kit. This helps ensure a smooth transition.
Depending on the sensitivity of the animals and the water parameters involved, the acclimation process may take anywhere from 30 minutes to a few hours.
Step 6: Adjust water volume if needed
If the water volume in the bucket becomes too high, you can remove some water and continue the drip acclimation process with fresh, dechlorinated water. Be cautious not to remove too much water, as it can lead to sudden changes in water parameters.
Step 7: Transfer the animals to the tank
Once the acclimation process is complete, gently net the aquatic animals from the bucket and transfer them to the tank. Avoid adding the water from the acclimation container to the tank to prevent any potential contamination.
Step 8: Dispose of the acclimation water
After transferring the animals, discard the acclimation water from the bucket. Do not pour it directly into any drains or natural bodies of water.
By following these steps, you can safely and gradually acclimate your shrimp, snails, and fish to their new tank environment after transport. Remember, it's important to monitor the process closely and make adjustments as necessary to ensure a smooth transition for your aquatic pets.